|
|
New solutions of converters for measurement of current-mode filters
Štork, Petr ; Kubánek, David (referee) ; Jeřábek, Jan (advisor)
This bachelor’s thesis describes some new solutions of differential converters that convert voltage to current and vice versa. Such converters are necessary for measurement of frequency filters in a current mode due to absence of instruments able to mesure signals with current as signal carrier. The goal is to design such converters that should influence gauged frequency properties in a current mode as little as possible. Converters will consist of operative amplifiers with current feedback. Converters designed this way are tested using simulations from PSpice programme, where particularly wideness of band of individual solutions is tested. Simulated solutions that are the most suitable ones are practicably re-enacted and gauged. These resuls of measurement and simulations are compared.
|
|
|
Analysis of methods of measurement of fully-differential frequency filters
Kučera, Tomáš ; Kubánek, David (referee) ; Jeřábek, Jan (advisor)
This bachelor thesis focuses on measurements methods of differential frequency -selection filters with active elements in current mode. Firstly it describes differential frequency-selection filters in current mode and conversions from voltage to current mode. Next the thesis deals with measuring of particular voltage converters to differential current and back from differential current to voltage, which is an integral part for measurements of differential frequency-selection filters in current mode. For design of particular converters there was used program OrCAD there and subsequent simulation was executed in program PSpice.
|
|
|
Design of new V/I and I/V converters for the measurement of current-mode filters
Jarník, Lukáš ; Polák, Josef (referee) ; Langhammer, Lukáš (advisor)
This master’s thesis deals with problems of analog differential converters, which are used in measuring circuits working in the current mode. The aim of this thesis is to propose a new voltage to current and current to voltage converter, that should influence measured frequency properties as little as possible. Commercial active elements are use to design converters. Active components are compared on the basis of properties as bandwidth and slew rate. Designed converters are simulated in Orcad PSpice program. Converters, of the best behavior are practically implemented and measured. Measured and simulated values are compared.
|
|
|
Analysis of methods of measurement of fully-differential frequency filters
Kučera, Tomáš ; Kubánek, David (referee) ; Jeřábek, Jan (advisor)
This bachelor thesis is analysing methods of measuring of differential frequency-selection filters with usage of active elements especially in current mode. Firstly it describes techniques of scheme of differential frequency-selection filters in current mode and conversions of linkage from voltage to current mode. Next the thesis aims at methods of measuring of particular voltage converters to differential current and back from differential current to voltage, which are an integral part for measurements of differential frequency-selection filters in current mode. For verification of characteristics of solutions designed separately as well as in cascade with particular solvent of frequency-selection filter there were used simulation instruments SNAP and OrCAD there, chosen resolutions were constructed and its characteristics were checked during laboratory test.
|
|
|
Analysis of methods of measurement of fully-differential frequency filters
Kučera, Tomáš ; Kubánek, David (referee) ; Jeřábek, Jan (advisor)
This bachelor thesis is analysing methods of measuring of differential frequency-selection filters with usage of active elements especially in current mode. Firstly it describes techniques of scheme of differential frequency-selection filters in current mode and conversions of linkage from voltage to current mode. Next the thesis aims at methods of measuring of particular voltage converters to differential current and back from differential current to voltage, which are an integral part for measurements of differential frequency-selection filters in current mode. For verification of characteristics of solutions designed separately as well as in cascade with particular solvent of frequency-selection filter there were used simulation instruments SNAP and OrCAD there, chosen resolutions were constructed and its characteristics were checked during laboratory test.
|
|
|
Analysis of methods of measurement of fully-differential frequency filters
Kučera, Tomáš ; Kubánek, David (referee) ; Jeřábek, Jan (advisor)
This bachelor thesis focuses on measurements methods of differential frequency -selection filters with active elements in current mode. Firstly it describes differential frequency-selection filters in current mode and conversions from voltage to current mode. Next the thesis deals with measuring of particular voltage converters to differential current and back from differential current to voltage, which is an integral part for measurements of differential frequency-selection filters in current mode. For design of particular converters there was used program OrCAD there and subsequent simulation was executed in program PSpice.
|
|
|
New solutions of converters for measurement of current-mode filters
Štork, Petr ; Kubánek, David (referee) ; Jeřábek, Jan (advisor)
This bachelor’s thesis describes some new solutions of differential converters that convert voltage to current and vice versa. Such converters are necessary for measurement of frequency filters in a current mode due to absence of instruments able to mesure signals with current as signal carrier. The goal is to design such converters that should influence gauged frequency properties in a current mode as little as possible. Converters will consist of operative amplifiers with current feedback. Converters designed this way are tested using simulations from PSpice programme, where particularly wideness of band of individual solutions is tested. Simulated solutions that are the most suitable ones are practicably re-enacted and gauged. These resuls of measurement and simulations are compared.
|
|
|
Design of new V/I and I/V converters for the measurement of current-mode filters
Jarník, Lukáš ; Polák, Josef (referee) ; Langhammer, Lukáš (advisor)
This master’s thesis deals with problems of analog differential converters, which are used in measuring circuits working in the current mode. The aim of this thesis is to propose a new voltage to current and current to voltage converter, that should influence measured frequency properties as little as possible. Commercial active elements are use to design converters. Active components are compared on the basis of properties as bandwidth and slew rate. Designed converters are simulated in Orcad PSpice program. Converters, of the best behavior are practically implemented and measured. Measured and simulated values are compared.
|
guest ::
